Press Alt + R to read the document text or Alt + P to download or print.
This document contains no pages.
HomeMy WebLinkAboutApproved PlansKECK HUNTINGTON EXTERIOR MONUMENT SIGN
SEPTEMBER 29, 2020
Conditionally Approved 11-5-20
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
2
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
GENERAL NOTES
Sign Contractor
A Sign Contractor who is able to prove demonstrated capability with a
complete project record satisfactory to the client and designer and who
is able to prepare shop drawings and samples, and to manufacture,
fabricate, assemble and install the work shown in these drawings.
Qualifications Submission (to be submitted with bid):
Sign Contractor must have a minimum of ten (10) years experience with
projects of similar scope
Sign Contractor must provide comprehensive list of projects of similar
scope
Responsibilities
The Sign Contractor shall assume responsibility for the quality of materials
and workmanship required for the execution of the work shown herein.
The Sign Contractor shall guarantee all materials and workmanship for
a period of (3) years following the final acceptance of the work. During
this period, if defects or faulty materials are found, the Sign Contractor
shall proceed immediately upon notification by the owner to remedy the
condition at his own expense, together with any damage to surrounding
finishes or furnishings which occurred as a result of those defects.
Codes
The Sign Contractor will be responsible for meeting any and all local, state,
and federal code requirements when fabricating and installing signs.
Submittals
Sign Contractor shall submit shop drawings for fabrication of all signs
(hard copy and electronic copy to be submitted). Fabrication pending
approval of all submitted drawings.
One (1) complete set of scaled layouts of each sign legend is required
for every sign (hard copy and electronic copy to be submitted). Scaled
layouts to be submitted showing overall sign sizes and cap-heights, project
typeface in specified sizes, margin criteria, kerning and leading. Client
responsible for verifying and approving all final copy prior to fabrication of
each sign.
Variations in quantities as determined by the Sign Contractor compared
with the message schedule shall be reported to the client and General
Contractor prior to submission of bid.
The design intent drawings submitted for bid are not fabrication drawings.
The Sign Contractor is expected to develop the final design and provide all
details necessary to effectively explain, show, and specify the fabrication
process, engineering, and the expected performance of the installed
product. The Sign Contractor must demonstrate through shop drawings,
details, and specifications their complete understanding of the desired
final product and the method/process by which they are producing said
product. The Sign Contractor is responsible for performing all field
measurements prior to submitting shop drawings/layouts/fabrication.
Repackaging/copying the design intent supplied drawings with new title
blocks and delivering them as submittals will not be accepted. Although
art may be supplied electronically for specified items, Sign Contractor
must be prepared to create all graphic content from scratch.
Where applicable, the Sign Contractor is to include signed engineering
calculations by a licensed engineer. Sign Contractor to furnish elevations,
sections, details of fabrication and erection, including all materials,
shapes, dimensions, finishes, wind load calculations, anchorage, and
method of connections for all sign types. Sign Contractor shall provide all
materials and parts necessary to complete each sign type, even though
such work may not be definitely shown or specified in design intent
drawings. The Sign Contractor shall provide all bolts, and anchors, support,
braces, connections, and other items necessary for completion of the
work.
Sample/Prototype Submittals
Pending approval of shop drawings the Sign Contractor shall submit to
General Contractor for approval, minimum 12” x 12” samples for each
finish, color and lettering type required. Sample submittal and approval
shall be for color, texture, and graphic image only. Compliance with all
other requirements is the exclusive responsibility of the Sign Contractor.
Pending approval of the above shop drawings and samples, the Sign
Contractor shall submit the following mockups using actual materials as
specified. Samples shall be submitted to General Contractor for approval.
GRAPHIC APPLICATION
Artwork
The Sign Contractor shall procure all typography and all necessary artwork
for reproduction, except where noted or otherwise specified.
Typeface
The typeface shall conform with project typeface specified. Alternate
typefaces will not be accepted. Letter and word spacing shall be optical
but in conformance with the examples shown on the drawings. Complete
alphabets, numbers, punctuation and symbols shall be submitted to
General Contractor for approval prior to any fabrication.
All letters, regardless of material or process, shall be executed in such
a manner that all edges and corners of finished letterforms are true and
clean. Letterforms with rounded positive and negative corners, edge build-
up or bleeding will not be accepted.
ADA
Unless noted otherwise, all signs, where applicable, shall comply with
ADA (American Disabilities Act) requirements in respect to type size,
proportion, contrast, tactile lettering and braille usage, and mounting
heights.
Codes and Regulations
The Sign Contractor shall be responsible for adhering to all applicable
building codes, regulations, covenants, ordinances and other regulatory
requirements that pertain to this project.
Walk-Through
The Sign Contractor shall arrange a meeting with the Client at the site for
the final location and alignment of sign elements and as required prior to
installation for items requiring site verification.
Installation
All signs shall be installed at typical/specific locations as specified in
the respective drawings, at mounting heights indicated and by methods
shown or specified. Sign Contractor to comply with relevant local union
requirements.
The Sign Contractor shall furnish information and coordinate with related
trades to assure satisfactory completion of the work. In all cases where
installation of mounting hardware involves other trades, coordination shall
be through the General Contractor. All installers will be of the appropriate
unions to assure labor harmony.
Exposed surfaces of work shall have a smooth finish, free of blemishes.
Where tight fit is required, joints are to be made to a close fit. Work
shall be accurately set to established lines and elevations and securely
fastened into place. Work shall be executed and finished in accordance
with approved drawings, cuts, details, and samples. Visible screw heads
and fasteners shall occur only at locations indicated on the drawings and
approved submittals. All edges and corners of finished letter forms and
graphics are to be true and clean.
Permits & Approvals
The Sign Contractor shall be responsible for obtaining all required permits,
and for review and approval coordination with Government, Township,
Local Community Board, DOT, and other agencies. If defined in their scope
as a deliverable, the Designer will assist by providing materials for these
review sessions.
Protection
The Sign Contractor shall protect the work and adjacent work and
materials from damage during progress of the work until completion.
Finished work shall be wrapped with paper, polyethylene film, or stripable
waterproof tape for shipment and storage and protection from damage
during installation.
Adjust and Clean
The Sign Contractor shall repair any damage incurred during installation
to the satisfaction of the Designer. Signs which cannot be repaired to a
new condition must be replaced. All sign surfaces must be clean, free of
smudging and fingerprinting. All hardware and electrical equipment are to
be adjusted to assure safe and proper operation and installation. All waste
and debris shall be discarded. The Sign Contractor shall arrange with the
general contractor for the use of waste receptacle.
Note: Sign Contractor to provide complete maintenance/ cleaning manual
for all sign types at project completion. Sign contractor to identify specific
products that comply with maintenance/cleaning specifications.
MESSAGE SCHEDULE AND LOCATION PLANS
Message Schedule
Room Number, Sign Number, Copy, and Quantity and any pertinent
remarks are listed in the message schedule. It is the responsibility of the
Sign Contractor to identify any differences in quantity between these
documents and obtain confirmation from client and General Contractor.
Copy and Graphics
The sign schedule shall indicate only the copy for each sign. Format for all
copy shall be as specified on the drawing sheet for each sign.
Location Plans
Each sign shall be located typically as indicated on the sign drawing sheet.
Conditions that may exist which prevent location of signage as specified
shall be brought to the client, General Contractor, and Architect’s attention
prior to installation.
PRICING
Bid Breakdown
The Sign Contractor shall provide unit prices for each sign type and
extended costs for the total quantity of each sign type. Please use the
provided Pricing Schedule for final bid submission. The cost of installation
shall be a separate lump sum for the phased project schedules outlined in
the Request for Proposal. Any tax required must be included.
Unit Price Guarantee
The Sign Contractor shall provide unit price guarantees for the duration
of the project. The Sign Contractor shall guarantee bid prices for 90 days.
The Sign Contractor shall also provide a unit price schedule to the owner
that will be guaranteed for a period of (1) year after completion of the job.
Installation charges should be included as a separate item in the schedule.
FABRICATIONS AND MANUFACTURE
Verification
The Sign Contractor shall verify and be responsible for all dimensions
and conditions shown on these drawings. Written dimensions shall take
precedence over scaled dimensions. Designer shall be notified of any
discrepancies in the drawings and/or graphic schedule, in field dimensions
or conditions, and/or changes required in construction details.
Fabricator shall stake sign locations for client approval prior to installation.
Delivery and Installation: The Sign Contractor shall be committed to deliver
and install signs in a timely manner, according to project requirements.
EXECUTION
Inspection
The Sign Contractor shall inspect condition of locations and surfaces
where signs are to be installed. The Sign Contractor shall not proceed with
installation until defects or errors which would result in poor installation
have been corrected.
Design Intent
The drawings were issued to show design intent, not actual fabrication.
The Sign Contractor will submit fully detailed shop drawings for stamped
approvals by Designer prior to fabrication. It is the responsibility of the Sign
Contractor to bring any discrepancies in these drawings to the attention of
the Designer prior to fabrication.
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
3
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
GENERAL PROJECT INFORMATION
VICINITY MAP NEIGHBORHOOD MAP
ARCHITECT CLIENT
515 South Flower Street, Suite 3700
Los Angeles, CA 90071
(213) 607-5907
125 W. Huntington Drive, Arcadia, CA 91007
125 W. Huntington Drive, Arcadia, CA 91007
SIGNAGE CONSULTANT
2110 Main Street, 207
Santa Monica, CA 90405
(310) 401-1339
PROJECT LOCATION
PROJECT CONTACTS
QTY PG #
GENERAL INFORMATION
General Notes -2
General Project Information -3
Typography and Materials -4
SIGN DETAILS
X01-Monument Sign 1 5-7
LOCATION PLANS
DRAWING INDEX
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
4
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
TYPOGRAPHY AND MATERIALS
AC1
MT1
SP1
SP2
SP3
SP4
SP5
SP6
FM1
FM2
FM3
FM4
FM5
FM6
FM7
FM8
ACRYLICS
Translucent White Acrylic
METALS
Horizontally brushed aluminum
SIGN PAINT
DARK GREY: MP 12795 Graynola; Satin Finish
BLACK: MP 33653 Black Stallion; Satin Finish
RED: To match PMS 201C; Satin Finish
WHITE: MP 27386 Verizon White; Satin Finish
SILVER: MP 18118 Vanadium Silver Metallic; Satin Finish
YELLOW: To match PMS 123C; Satin Finish
FILM
3M Matte White 7725-20
3M IJ180mC-10,Digitally Printed Vinyl for wall application with
3M 8500M-301, Riverbed overlaminate.
3M Dual Color Film Black 3635-222
3M Dual Color Film White 3635-210, painted and to match PMS201C.
Ensuring perferation is clear.
3M Matte Black 7725-12
3M™ Scotchcal™ Clear View Graphic Film IJ8150. Optically clear vinyl film
with digitally printed graphic at 70% White.
3M Translucent White 3630-20
3m Golden Yellow 3630-125
TYPOGRAPHY SCHEDULE MATERIALS
NATIONAL MEDIUM
NATIONAL REGULAR
NATIONAL BOOK
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz
* Vendor responsible for licensing all fonts required for duration of project.
https://klim.co.nz/retail-fonts/national/
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
5
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
/,1$&9$8/7
(1&/2685(
MONUMENT SIGN
/,1$&9 $8 /7
(1&/26 8 5 (
10'-0"
5'-0"
4’-0"
21’-0"
MONUMENT SIGN LOCATION PLAN
SCALE: 1/8”=1’-0”1
X01MONUMENT SIGN SITE PLAN
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
6
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
WESTHUNTINGTON DRIVE Fertility clinic practice Cast in Place
Concrete Sign
Base, with
sack rubbed finish.
Letters on sign
to have 1” returns
as per city request.
ELEVATION
SCALE: 3/8" = 1'-0"1 SECTION A-A
SCALE: 3/8" = 1'-0"2
RENDERING
SCALE: NTS3
A
A
AC1 FM7
AC1 FM8
MT1 SP3 MT1
To match building
exterior dark navy
MT1 SP2
AC1 FM7
MT1 SP5
3'-0"
6'-8"
8'-0"
1'-4"
10’-0"
18’-0"
5'-0"10"
1'-0"
1'-0"
3 1/8"
3 1/8"
6 3/4"
NIGHT VIEW
X01MONUMENT SIGN
KECK HUNTINGTON
125 W. Huntington Drive, Arcadia, CA 91007
7
PAGE
EXTERIOR MONUMENT SIGN
September 29, 2020Project No. J118
20200929_Keck Huntington_Exterior Signage
NOT FOR CONSTRUCTION All content Copyright© 2020 Altitude
Design Office (Designer). All drawings and material appearing herein
constitute original and unpublished work of the Designer and may not be
duplicated, used or disclosed without written consent of the Designer.
These drawings represent design intent only. Signage Contractor shall be
responsible for further developing designs for constructibility, structural
and performance soundness, and conformance with field conditions.
X01: 144 SQFT
WESTHUNTINGTON DRIVE Fertility clinic practice
70'-8 5/8"
43'-11 1/2"
ELEVATION
SCALE: 3/32" = 1'-0"1
18’-0"
8'-0"
X01MONUMENT SIGN